Product: Straight Curb & Gutter Forms


 

The Dee straight curb and gutter forming system consists of a back form, a front form, a face form, a division plate, and a top spreader. The back and front forms are standard straight flatwork forms with the back form taller than the front form.

 

The Dee straight curb and gutter forms are normally assembled into a curb and gutter forming system as shown in the illustration below.

 

Concrete Form

There are 5 basic types of straight curbs:

  1. Vertical face - a setup with the front and the back of the curb being at 90° angles
  2. Battered face - a curbface with the back of the curb at a 90° angle and the front at less than a 90° angle
  3. Bottom radius - a battered curbface with a single radius formed into the bottom of the curb
  4. Top and bottom radius - a battered curbface with a radius formed into the top and bottom of the curb
  5. Drive over - a curbface with a slow, gradual batter allowing traffic to pass over

Dee straight curb and gutter forms are used primarily to form traffic barriers and direct water to sewers, culverts or ditches. Water can be directed away from the curb (out flow), or towards the curb (in flow) depending on the curb and gutter configuration.

 

Typical Applications:

  • Streets
  • Roadways
  • Parking lots
  • Driveways

Self-aligning

Form assembly is easier, faster and more cost effective

Reinforced gussets and heavy gauge, 7-gauge steel stake pockets

Strongest concrete placement forms in the industry providing many years, even decades, of useful life

2 or 3 heavy-duty, welded-on, 7-gauge steel stake pockets with built-in wedges with a bent tip

Setup and removal is quick and easy making lost wedges a thing of the past

Double flanges with full-height heavy steel noses

Extra form strength and long-life

Heavy-duty noses

Better form alignment providing truer placements

Few moving parts (other than the heavy-duty wedges that lock the form securely to the form pin for firm steady fastening)

Setup and removal is quick and easy

Height adjustability

Keeps form in line for simple curb & gutter forming on non-graded areas

Available with a 2" or 4" base

Added stability

All-welded (not riveted like many competitor forms) to increase the form strength and rigidity

Guaranteed accurate forming and improved form longevity

4 factory punched bolt holes in each rail

Effortless attachment to other forms or forming accessories (like division plates)

Taller than 8" in height are manufactured with two steel noses, welded between flanges, and reinforced with an angle

Increased strength and flexibility by allowing both single and multiple sized forms to be joined

Taller than 8" in height are manufactured with heavy gauge steel stake pockets with wedges placed in opposing directions

Guaranteed securely anchored forms to prevent misalignment

Available with custom manufactured curbface forms

Match any curb profile

Accomodates high strength steel form pins

Prevents misalignments during placement

Curbface form can be locked in place (by using a top spreader)

Ensures matched specifications and passed inspections

Heavy steel angles welded at both ends of all forms

Significantly minimized end damage to reduce expenditures for replacement forms

Standard 2" top rails

Easy combination with competitors' forms (by using dee's filler form accessory)

Regarded as the industry standard (often copied, but never duplicated)

You are buying the best product available on the market


Straight Curb & Gutter Forms Specs & Sizes
Available in heights from 4" to 7 1/2" in 12-gauge steel, and from 4" to 24" in 10-gauge steel, Dee's straight curb and gutter forms are offered in standard 10' lengths with either 2" or 4" bases, but can also be obtained in shorter lengths.

Dee straight flatwork forms are available with 2 or 3 pockets on up to a 12" height and only 3 pockets for form heights above 12".

Custom forms available in 1/2" increments.


Additional options for curb & gutter flatwork forms

Sliding Nose
A sliding nose (dee product #911) is a piece that retracts to allow adjacent forms to be removed from the pour without removing forms from either side of the form. Using this type of nose is the only way forms can be easily removed from a pour when using dowels or rebar.


Dowel Holes
Dowels, or rebar material, travel through the face of the flatwork form. After the forms are removed and adjacent concrete is placed, the two placements are interlocked by the rebar or solid dowels.

Dowel holes are punched slightly larger than the diameter of the solid dowels or rebar to be used allowing the flatwork forms to be easily slipped off the dowels after the concrete placement is complete.

Forms punched for dowels or rebar may require a sliding nose to allow the form to be removed after placement without damaging the reinforcement material.


Dowel Hole Specifications (can be punched on):

  • 6” to 30” O.C. as specified
  • 10-gauge or 12-gauge forms
  • 3/16” and 1/4” forms

Dee’s Straight Curb & Gutter Forms Parts List
Dee's Straight Curb and Gutter Forms are custom made to your specifications. The table below lists the ranges of sizes available for each of the parts needed to complete a configuration. Maximum form lengths are 10’0” lg.

To view an image of any of our products listed in the table below, just roll over the dee product number.

PartHeightsDescriptionDEE   Product # 
Straight Back Form 4" - 24" Straight back form - 2"   base                            
205 View    Part      
4" - 24" Straight back form - 4" base 216 View Part
Straight Front Form 4" - 24" Straight front form - 2" base 205 View Part
4" - 24" Straight front form - 4" base 216 View Part
Straight Curb Face Form 6" - 12" Straight curb face form - Types J, B, S or A 240 View Part
6" - 12" Straight form used as curb face form - Type A 205 View Part
Top Spreaders 4" - 9" Top spreaders - Types J, B or A 301 View Part
4" - 9" Top spreaders - Type S 302 View Part
Division Plates most Full division plate - Types J, B, S or A 337 View Part
most Skeleton division plate - Types J, B, S or A 338 View Part
most Full rollover division plate - Type E 350 View Part
most Skeleton division plate - Type E
351 View Part

Commonly Ordered Sets for Straight Curb & Gutter Forms

There are 5 basic industry-standard configurations for straight curb & gutter concrete placement forming. Click one of these configurations below to view the ordering specs:

Copyright Western Hardscape Supply, Inc. © 2017. All Rights Reserved.